DISCLOSURE: TheRuggedRooster.com is reader supported so if you buy any products featured on this site I may earn an affiliate commission. As an Amazon Associate I earn from qualifying purchases. Read my full disclosure here.
Occasionally, everyone has issues with their Husqvarna chainsaw. I’ve used the machine before and have experienced a few problems.
As a result, I’ve decided to share with you seven common issues I’ve encountered with my Husqvarna chain saw over the years.
1. Trouble Shooting
Troubleshooting is one of the common issues with Husqvarna chainsaws.
The complication can block air filters when they draw more gas than air.
When you run a saw with impassable air filters, the engine produces incomplete combustion fuel, which leads to more carbon deposits.
After every use, clean the chain saw correctly. Similarly, you can run the saw without the bar to ensure the oil is being pumped effectively.
2. Chain Cutting Problems
The quality of sharpening your Husqvarna chain saw is usually the source of how the chain cuts.
If the chain cuts incorrectly or at an angle, then it means you’re filing the cutters at different angles or exerting uneven pressure on one side over another.
Throughout your chain, the angle of the top plate and the size of the cutter should be uniform.
Similarly, if the rakers or depth gauges of your Husqvarna chain saw are filed down too much or too little, your chain will cut too deep or barely cut at all.
If your chain becomes dull soon, there are a few possibilities. Ensure you’re using the effectively sized file for your chain by consulting your user’s handbook.
3. Oil Line Clog
The automatic oiler on Husqvarna chain saws systematically pumps small amounts of oil from the oil tank through the attached oil line and onto the guide bar and chain.
However, if the line becomes blocked, the oil will not reach the chain, putting you and your machine at risk.
When there’s little to no lubrication on the chain, it’s a sign that the oil line on the Husqvarna chain saw is clogged.
When keeping the Husqvarna chain saw without wiping the oil channel and groove in the guide bar and chain, the oil can harden and clog the exit line, especially over time.
Clean the oil hole and oil outflow port on your chainsaw by removing the chain and bar. If this doesn’t work, the oil line or pump will most likely need to be replaced.
4. Compression Problem
If your Husqvarna chainsaw doesn’t start when you pull the starter rope, the compression can be the problem.
There are different moving parts, and a certain amount of compression is needed to keep these pieces moving.
The engine generates compression through the crankcase and combustion chamber.
Because the engine can’t keep enough pressure in the cylinder to function appropriately when compression is too low, you may notice a loss of power or a complete shutdown.
Placing the chainsaw on the ground and lifting it with the starting rope is easy to check for low compression.
If the rope slowly increases, the chainsaw (see also: Chainsaw alternatives) compression is low and must be checked more thoroughly.5. Stalling
Does your Husqvarna chainsaw start-up and stall right away? The cause of these actions could be hidden in the carburettor.
The stalling problems can be caused by a faulty fuel pump or a faulty main fuel jet.
Under some conditions, the chainsaw cannot function correctly and just stalls which may cause the chainsaw to be dangerous.Improper carburettor adjustment or air leaks through the crankshaft oil seals or carburettor gasket are two essential causes of this performance.
If cleaning the carburettor does not work, it should be rebuilt or replaced entirely.
6. Loosens And Vibrations
Dynamic forces, sawing modes, imbalanced moving parts, shocks in gears, bearings, and other factors trigger the Husqvarna chain saw vibrations.
Similarly, the interaction between the operator, the machine, and the processed wood affects chainsaw vibration levels.
Kickback and the likeliness of the saw chain being thrown off the guide bar are increased.
7. Grimy Air Filters
Your Husqvarna chainsaw may not start due to a blocked air filter.
The engine will not have enough air to combust if the filter is blocked.
Because the air filter’s job is to keep debris out of the engine, it commonly becomes stuck with the dirt and grime it’s supposed to keep out.
An obstructed air filter can result in a loss of engine power, increased fuel consumption, and excessive wear on engine parts.
Inspect it for wear and tear when you clean the air filter on your Husqvarna chainsaw. These are symptoms that your chainsaw needs to be replaced.
The common Husqvarna chain saw problems are
- Trouble Shooting
- Chain Cutting Problems
- Oil Line Clog
- Compression Problem
- Stalling
- Loosens And Vibrations
- Grimy air filters
However, following a simple manual guide and regular cleaning will keep the Husqvarna chain saw in good shape and increase its lifespan.