DISCLOSURE: TheRuggedRooster.com is reader supported so if you buy any products featured on this site I may earn an affiliate commission. As an Amazon Associate I earn from qualifying purchases. Read my full disclosure here.
The best thing about DIY methods is that you can make the process easy and customise according to your needs.
That is why I always like to use a simple and effective tool to repair or replace parts of my roof.
Working with different pieces may result in undesired results.
When you use nails to join parts, you will need a tool to make the process easy and less tedious.
In my years of experience, I realised that a quality nail gun is the best tool for joining parts using nails. It is important to sort out this boring task in the shortest time possible.
There are several nail guns in the market.
However, you will need to select the best one, and there is nothing better than a pneumatic nail gun!
When buying a pneumatic nail gun, you need to know how it works to get the most out of it.
This article is about some of the crucial steps you need to follow to successfully use a pneumatic nail gun.
Steps of using a pneumatic nail gun
The nail gun is compatible with any project that you can use a simple hammer and nail.
For large projects like fence installation and framing, a pneumatic nail gun can increase stability and consistency and cut the working time. Follow the steps below to effectively use your nail gun.
Step 1. Fill the nail gun magazine with nail strips
Different manufacturers use different designs on their tools, but magazine access is always toward the bottom or back of the tool.
Slide nail strip into the magazine and close it.
Step 2. Wear safety glasses before turning on the nail gun
There is a contact trip trigger in most pneumatic nail guns.
When nailing a surface, you will need to compress the nail gun to push the nail in.
Nails cannot come out of the gun without engaging the trigger, but it is important to take precautions.
Step 3. Practice using the gun on scraps before the project
This nail gun work by pressure. Therefore, the time you apply the pressure and the amount of pressure matter when using it.
It is important to practice before the actual project. This will help you use the nail gun more effectively.
Step 4. Put the nail gun tip against the surface to nail
Hold the gun handle with one hand to have an easy time accessing the trigger. You need to support the nail gun and keep it in place.
Your body should be away from the pneumatic gun but close enough to offer the required stability.
This is because the gun will have a kickback when fired.
Step 5. Exert pressure of the gun tip against the surface
Never exert pressure using your stomach or chest since it may lead to severe injuries. Pull and release the trigger immediately.
You should avoid multiple nails shooting and jumping off the gun by avoiding holding it down.
Step 6. Remove the gun from the nailed surface
You should apply enough pressure to ensure that nails are not crooked. The crooked nail may be a result of pulling the gun too quick.
Step 7. Disconnect the gun
After you finish nailing, you should disconnect the pneumatic nail gun (see the best nail guns for crafts) from the power source.
You should also disconnect the gun before reloading new nail strips to avoid unnecessary nail firing.
How pneumatic nail gun works
A pneumatic nail gun is powered by compressed air. You will require a compressor and an air hose to use this type of nail gun (see the best nail gun for hardie siding).
The compressed air is responsible for driving the nail into the surface by driving down the hammer to hit the nail at the barrel.
You need to pass a safety mechanism before releasing compressed air. The rigger valve mechanism is responsible for powering a pneumatic nail gun.
A pneumatic nail gun will not fire until your press the plunger onto the surface to join or fasten.
When you pull the trigger, the valve is released to allow air to flow through the chamber.
The plunger will act on the hammer once the plunger is depressed onto the material.
The force created by the compressed air will drive down the hammer, which hit the nail in the barrel and into the material.
The blade is attached to the hammer. The primary use of the blade is to separate the fire nail and others on the strip.
That’s How A Pneumatic Nail Gun Works
Nowadays, you can have all your projects are completed efficiently and effectively, thanks to a pneumatic nail gun.
Following the above steps, you will have an easy time using a pneumatic nail gun any time.
Safety is the most important thing you should consider when using a pneumatic nail gun.
Wear protective equipment like gloves and glasses to avoid injuries.
The pneumatic nail gun has simple and easy-to-operate parts that you can master by reading the above guide.