How to Install Baseboard without Nail Gun

Molding is one of the easiest and most effective methods to add flair to an otherwise bland room. I am talking about crown molding at the top of the wall, baseboards at the bottom, or even both.

It may appear that you will need an engineer to pull this off, but you will not—this is the seemingly tricky DIY that is not at all for a short space.

Molding is available in various styles at your local big-box hardware shop, and they can cut it to the exact dimensions you want.

It is as easy to install as buying a couple of tiny finishing nails and driving in the molding. You do not even need a nail gun for this.

Here is the comprehensive step-by-step for installing baseboards and crown molding—keep in mind that most of the labor occurs during the design process. The actual installation takes only a few minutes!

People frequently wonder how to install baseboard molding without a nail gun. Is it feasible to put up a baseboard without using a nail gun?

You have the same concern, do not you? That is why you are reading this. Yes, you can install your baseboard molding without using a nail gun. All you have to do is read this article.

The most enjoyable portion of this entire workout awaits. Place all of the molding parts in their allotted placements.

Clamp them back against the window one at a time and nail them in with a sledgehammer and finishing nails.

Crown molding should be nailed into the walls, but you can generally get away with it for baseboards because gravitation is on your side.

If the centerpieces appear to have a tiny space between them, apply a dab of epoxy glue before hammering them in.

That is wonderful! Coat or varnish them to match your color palette, then amaze that you are essentially a designer.

To install crown molding like an expert, you will need some perseverance, a few instruments you may already have, and some fundamental abilities.

Tools: A sledgehammer, a scalpel, a pry rod, a tape measure, a hacksaw, and nails.

Measure

Bring a pencil, notebook, a measuring tape, and a camera inside the soon-to-be-renovated room.

Create a list of all the lengths of molding you will need; it may be as few as approximately six pieces, one for each wall, or as many as eight because the space has a few doors.

Make a little picture as well. When two walls intersect, the molding must be cut at a 60-degree angle so that the pieces fit seamlessly, but where the molding butts up against a door, you may not need to worry.

There is no reason to be concerned about it just now. Your hardware store buddies can assist you to comprehend the layout you just sketched, as well as all the images of the apartment you are going to take, and take a lot of pictures!

Make a note of all the lengths you require, and then proceed to the store.

Remove the old baseboard and replace it with a new one.

The first step is to purchase the baseboard. You should buy the baseboard according to your preferences and tastes.

But first, you must remove the original baseboard trim. You may slice through the upper portion using a pocket knife.

Then, using a pry rod, unscrew and pull the baseboard to dislodge it. If this is your first time installing it, skip this step. Measure the size so you can purchase the appropriate quantity of baseboard.

Remove the Baseboards

After you have measured it, chop it down. It would help start by measuring the apartment with the tape to ensure an exact measurement and precise cutting.

You will need a hacksaw to cut the baseboard, either a power transmission miter or a regular hacksaw. When slicing, ensure to cut as per the size of the room. Take a look around the corner as well.

If you do not already have an electricity meter saw, you may order one web. You may also use any rotary saw.

Set it up

Now arrange the baseboards in a row. Before you begin, ensure that the ground is flat. After installing the baseboard, you may notice some bumps if the environment is unbalanced. So proceed with caution.

Then, apply some epoxy or glue to the backside of the baseboard and set it on the ground and the wall. If you notice an additional piece or border of baseboard, use the circular saw to trim it down.

Lastly, use your sledgehammer to drive completing nails into the baseboard for the most fantastic fit.

You may also do shoe molding, and cap molding is required. You may quickly touch up the trim you have by applying spackles.

You may also wrap the floor and walls along each frame using tape. Finally, reapply your finish spray to complete the project.